广东佛山QF1NS-31.5-40锥密封焊接球阀
叶轮上的内外表面要求光滑，以减少水流的摩擦损失。泵体也称泵壳，它是水泵的主体。起到支撑固定作用，并与安装轴承的托架相连接。泵轴的作用是借联轴器和电动机相连接，将电动机的转距传给叶轮，所以它是传递机械能的主要部件。轴承是套在泵轴上支撑泵轴的构件，有滚动轴承和滑动轴承两种。滚动轴承使用牛油作为润滑剂加油要适当一般为2/3～3/4的体积太多会发热，太少又有响声并发热。滑动轴承离心泵结构使用的是透明油作润滑剂的,加油到油位线。

商品描述
订货示例／ Ordering Code
KHSAE (3)(4)(5)(6)(7)(8)(9)(1o (1) 2
(1）名称代号： KHSAE 法兰式球閥
Name code : KHSAElange type bal valve
(2）公称压力／ Nominal pressure :210-21MPa 420-42MPa
(3）公称通径／ Nominal diameter :15-125mm
(4）閥体材料/ valve body material : 2﹣碳钢／2-Carbon steel 4﹣不锈钢／4-stainless steel (
(5）球体和阌杆材料／ Valve body and valve rod :1﹣碳钢／1-Carbon steel ,4﹣不锈钢／4-stainless steel
(6）球体处密封：2-POM,4﹣聚四氟 Sealing at valve body :2-POM4-teflon
(7）閥杆和接头处密封／ Sealing at valve rod and connector : A ﹣丁晴橡胶＋支撑国／ A - NBR + Supporting ring B ﹣氟橡胶＋支撑图／ B - Fluororubber + Supporting ring B - EPDM ＋支撑困／ B - EPDM + Supporting ring
(8）手柄型式／ Handle type
02＝铝质抱箍式手柄，曲柄（ AK )02= aluminum hold loop handle , crane handle ( AK )
06＝钢质带固定螺栓式的手柄，曲柄（ SK )
06= steel handle with installation bolts , Crane handle ( SK )
07＝钢质可拆卸手柄（DN80-DN125)/07= Steel removable handle (DN80-DN125)
(9）系列／ Series （由制造商定）/( by the manufacturer )
(10）表面保护／ Surface protection 无＝确化／ None = phosphorization G ＝镀黄锌／ G = yellow Zinc plating W ＝环保锌（三价格）/ W = Environmental protection zinc ( trivalency ) 产品简介／ Production Overview KHSAE 系列法兰式球是一种接口采用 SAE 标准的二通球脚。 SAE 标准法兰可重机标准 JB /EQ4187974 体式高压法兰互换。
KHSAE series flange ball valve is a twO - way ball valve adopting SAE standard . SAE standard flange m exchange with JB -EQ4187-97 separating high presSure flange .


2LQF4W-A/4.0,2LQF4W-A/4.5,列管式油冷却器冷却器,列管式油冷却器,LQ系列冷却器无锡温纳厂家
2LQF4W-A/5.5,列管式油冷却器列管式油冷却器冷却器,列管式油冷却器,LQ系列冷却器无锡温纳厂家
订货示例／ Ordering Code
KHZ DN13 SAE420 (1) (3 4)(5)(6
(1）产品型号／ Product model : KHZ 10
(2）公称通径／ Nominal diameter :DN13-50
(3）压力标准／ Standard connection :SAE210(210bar)SAE420(420bar)
(4）体，接头体材料：1﹣碳钢4﹣不锈钢 Valve body and connector materials :1-Carbonsteel4-StainlesS steel
(5）球体和控制芯轴材料：1﹣碳钢4﹣不锈钢 Valve b0dy and cOntrol COre shaft material :1-Carbonsteel4-StainlesS steel
(6）球体密封材料：2﹣聚甲醛4﹣聚四氟 Ball seal materials :2-polyformaldehyde4- ptfe
(7）闼体与接头、控制芯轴密封圈材料： E ﹣丁晴橡胶 F ﹣氟橡胶 Body and joint , control core shaft sealing ring material : E - NBR F - fluororubber
(8）手柄代号：02﹣铝合金式曲柄06﹣钢式曲柄 The crank handle code :02- aluminum alloy type of crank 06- type steel crank
(9）系列／ Series （由制造商定）/( by the manufacturer )
(10）表面保护／ Surface protection 无＝磷化／ None = phosphorization G ＝镀黄锌／ G = yellow zinc plating W ＝环保锌（三价格）/ W = Environmental protection zinc ( trivalency )
广东佛山QF1NS-31.5-40锥密封焊接球阀

wenna6613.b2b168.com/m/